***This Product Has Been Phased Out, You Can Find A Suitable Replacement in WISE-7118Z or WISE-7118Z/S2***
WISE (Web Inside, Smart Engine) is a product series developed by ICP DAS that functions as control units for use in remote logic control and monitoring in various industrial applications. WISE offers a user-friendly and intuitive web site interface that allows users to implement IF-THEN-ELSE control logic on controllers just a few clicks away; no programming is required. With its powerful and easy-to-use features, it will minimize the learning curve, shorten time to market and dramatically reduce the effort and cost spent on system development.
WISE-7119 follows IEEE 802.3af-compliant (classification, Class 1) Power over Ethernet (PoE) specification. It allows receiving power from PoE enabled network by Ethernet pairs (Category 5 Ethernet cable). This feature provides greater flexibility and higher efficiency therefore simplifying systems design, saving space, reducing cables and eliminating the requirement for dedicated electrical outlets. Meanwhile, in case under a non-PoE environment, WISE-7119 will still be able to receive power from auxiliary power sources like AC adapters or battery, etc.
This multi-function module WISE-7119 supports Modbus/TCP protocol to make seamless integration with SCADA software available. It features 16-bit, 8-channel differential analog inputs and 4-channel digital ouputs. Each analog channel is allowed to configure an individual range and has 240 Vrms high over voltage protection.
- Built-in Web Server for IF-THEN-ELSE rule setting
- Built-in IF-THEN-ELSE rule engine for logic operation
- No more programming. Just click and get done!
- Support IO, Counter, Timer, Email operations
- Modbus/TCP Protocol for SCADA Software Seamless Integration
- IEEE 802.3af-compliant Power over Ethernet (PoE)
- 10/100 Base-TX Ethernet
- Support Current Input, Voltage Input and Thermocouple Input
- Over Voltage Protection is up to 240 Vrms
- 4-channel Digital Outputs
- 2-way Isolation/ESD Protection
Building Automation, Factory Automation, Machine Automation, Remote Maintenance, Remote diagnosis and Testing Equipment, etc.
Reference & Support
|Input Channels||8 (Differential)|
|Input Type(jumper selectable)||+/-15 mV, +/-50 mV, +/-100 mV, +/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V|
|Thermocouple (J, K, T, E, R, S, B, N, C, L, M,LDIN43710)|
|+/-20mA, 0~20mA, 4~20mA|
|Sampling Rate||10 samples/Sec. total|
|Accuracy||+/-0.1% or better|
|Zero Drift||+/-10 μV/°C|
|Span Drift||+/-25 ppm/°C|
|Input Impedance||Voltage||>1 MΩ|
|Common Mode Rejection||86 dB Min.|
|Normal Mode Rejection||100 dB|
|Over Voltage Protection||240 Vrms|
|Individual Channel Configuration||Yes|
|Open Wire Detection||Yes|
|Output Type||Isolated Open Collector (Sink)|
|Max. Load Current||700 mA/Channel|
|Load Voltage||5 VDC ~ 50 VDC|
|Overvoltage Protection||60 VDC|
|Overload Protection||1.4 A|
|Flash Memory||512 KB|
|PoE Ethernet Port||10/100 Base-TX and automatic MDI/MDI-X|
|2 Way Isolation|
|ESD (IEC 61000-4-2)||4 kV Contact for each terminal and 8 kV Air for random point|
|EFT (IEC 61000-4-4)||+/-4 kV for Power|
|L3||Ethernet 10/100M Speed|
|Reserve Polarity Protection||Yes|
|Powered from terminal block||Yes, 12 ~ 48 VDC|
|Powered from PoE||Yes, IEEE 802.3af, Class1|
|Dimensions(W x L x H )||123 mm x 72 mm x 35 mm|
|Installation||DIN-Rail or Wall mounting|
|Operating Temperature||-25°C ~ +75 °C|
|Storage Temperature||-30°C ~ +80 °C|
|Relative Humidity||10 ~ 90% RH, non-condensing|
|Rule Configuration Website||Access Web server on WISE controllers to edit and upload logic rules through web browser.|
|36 IF-THEN-ELSE Logic Rules||3 IF conditions with AND or OR operators
3 THEN actions and 3 ELSE actions
|48 Internal Registers||Hold temporary variables and read/write data via Modbus/TCP address.|
|12 Timers||Delay / Timing functions.|
|12 Emails||Send Email messages to pre-set Email receivers.|
|12 CGI Commands||Send pre-set CGI commands.|
|12 Recipes||Set up THEN/ELSE action groups.|
|8 P2P remote modules||Set up the connection information for the remote WISE modules.|
|Modbus/TCP Protocol||Real time control and monitoring I/O channels and system status of controllers via SCADA software.|
|AI Channel||=, >, <, >=, <=(value)|
|DO Counter||=, >, <, >=, <=(value), Change|
|Timer||Timeout, Not Timeout|
|P2P||DI, AI, DI counter, DO counter, IR|
|Rule Status||Enable, Disable|
|THEN / ELSE Actions|
|DO Channel||ON, OFF, Pulse Output|
|Internal Register||Change the value|
|P2P||DO(On/Off), AO, IR|
|Rule Status||Enable, Disable|
User-defined I,O Exp...
Data acquisition con...
Small Industrial Enc...
24V , 0.25A 6W Power...
5-port Industrial Un...
Unmanaged 5-Port Ind...