- Automatic MDI/MDI-X crossover for plug-and-play
- Each port supports both 10/100 Mbps speed auto negotiation
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- Supports wide operating temperatures from -30°C ~ +75°C
- Built-in Cyber-Ring redundant technique
- Redundant Dual Power Inputs +12 VDC ~ +48 VDC
- Power failure alarm by relay output
- Modbus remote monitoring
- Supports Modbus OPC Server
- Store-and-forward architecture
- Frame buffer memory: 1 Mbit
- 2048 MAC addresses
- 3.2 Gbps high performance memory bandwidth
- Single-mode 40Km, SC Connector Fiber supports
- DIN-Rail Mounting or Wall Mounting
The MSM-508FCS-40T is an 8-port Industrial Ethernet Layer 2 Managed Switch with 2-Fiber Port that secures data transmission by using fiber optic transmission to provide immunity from EMI/RFI interference. It is perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.
It can be managed through RS-232 port via serial console or Ethernet port using telnet or Web browser. In addition, the switch supports a lot of powerful managed functions, such as 802.1Q Tag-based VLAN, Portbased VLAN, 802.1p QoS (Quality of Service), Port Trunking, Spanning Tree, Cable Testing and Port Mirroring.
Built-in ICP DAS Cyber-Ring technique that enable multiple switches to be placed into a redundant ring. Typically it detects and recovers from a fiber or copper link failure within approximately 20 ms V for the majority of applications a seamless process. Modbus/TCP, Modbus/RTU and OPC supported, SCADA application can monitor status of Ethernet and fiber port with Modbus or OPC protocol.
MSM-508F provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the it's power needs. And the relay output facility can deliver warning signal while power or network link failure.
|Status||10/100M, Link/Act, Full duplex/Half duplex (Fiber Port)|
|Ports||6 x RJ-45, 10/100Base-TX|
|Standards||IEEE 802.3, 802.3u and 802.3x|
|Processing Type||Store & forward, wire speed switching|
|Memory Bandwidth||3.2 Gbps|
|Frame Buffer Memory||1 Mbit|
|Flow Control||IEEE 802.3x flow control, back pressure flow control|
|Protocol||VLAN, QoS, Port Trunk, SMTP, TELNET|
|Redundant Strategy||STP, Ring (ICP DAS)|
|Isolation||1500 Vrms 1 minute|
|DIP Switch||Yes, Normal Run / Repair Mode|
|Ports||2-port 100 Base-FX
|Fiber Cable||8.3/125, 8.7/125, 9/125 or 10/125 µm|
|Distance||40 km, (9/125 µm recommended) for full duplex|
|Wavelength||1300 or 1310 nm|
|TX Output||-5 dBm Min.
0 dBm Max.
|RX Sensitivity||-35 dBm|
|ON Voltage Level||+19 VDC ~ +30 VDC|
|OFF Voltage Level||+11 VDC Max.|
|Sink/Source (NPN/PNP)||Sink (NPN)|
|Load Current||30V/100 mA Max.|
|Ports||1 x RS-232 (Console)
1 x RS-485
|Reverse Polarity Protection||Yes|
|Input Range||+12 VDC ~ +48 VDC Redundant Dual Inputs (Non-isolated)|
|Redundant Power Inputs||Yes|
|Consumption||0.3 A @ 24 VDC|
|Alarm Contact||Yes,Relay 2 A @ 30 VDC|
|Dimensions (mm)||DIN-rail mounting: 47 x 175 x 142 (W x L x H)
Wall mounting: 51 x 190 x 142 (W x L x H)
|Installation||DIN-rail mounting or wall mounting|
|Ingress Protection Rating||IP30|
|Operating Temperature||-30 ~ +75°C|
|Storage Temperature||-40°C ~ +85°C|
|Humidity||10 ~ 90% RH, non-condensing|
8-Port Industrial 10...
8-Port 10,100 Base-T...